product information *the information contained herein is presented only as a guide for the applications of our products . no responsibility is assum ed by toshiba matsushita display technology or ot her rights of the third parties which may re sult from its use. no license is granted by implication or otherwise under any pat ent or patent rights of toshiba matsushita display technology or others. *the information contained herein may be changed without prior notic e. it is therefore advisable to contact toshiba matsushita display technology before proceeding with the des ign of equipment incorporating this product. (1/10) 2008-02-21(ver.0.2r) 38cm color tft-lcd module (15.0 type) LTA150B851F (a-si tft) toshiba matsushita display technology co., ltd all information is sub j ect to chan g e without notice. please read bottom notes. features tentative (1) 15.0 xga color display with high luminance (2) built in long life lamps(mttf:50,000 h) rohs compatible ( condition/ t a:25 c, i fl :6ma(rms)(continui ng lighting), f fl :50khz ) (3) replaceable structure of lamp mechanical specifications item specifications dimensional outline (typ.) 348.0 ( w ) x 254.7 ( h ) x 14.0 ( d ) mm mounting hole(w) : 340.0 mm number of pixels 1024 (w ) x 768 ( h ) pixels active area 304.128( w ) x 228.096( h ) mm pixel pitch 0.297 ( w ) x 0.297 ( h ) weight (approximately) 1300g backlight sidelight ( 4 ccfls ) absolute maximum ratings item min. max. unit (v dd ) -0.3 4.0 v supply voltage (v fl ) 0 2.0 kv(rms) fl driving frequency ( f fl ) --- 100 khz input signal voltage ( v in ) -0.3 v dd +0.3 v operating temperature *1 -10 70 c storage temperature -20 80 c storage humidity (max. wet bulb temperature = 39 c) 10 90 %(rh) *1: wet bulb temperature should be 39 c max., and no condensation of water. electrical specification ( t a=25 c ) (recommended operation condition) item min. typ. max. unit remarks (v dd ) 3.0 3.3 3.6 v supply voltage (v fl ) --- (650) --- v(rms) i fl =6.0ma(rms) fl start voltage (v sfl ) (1500) --- (1900) v(rms) t a=-10 c differential input voltage ( v id ) 0.1 --- 0.6 v common mode input voltage ( v cm ) 1.1 --- 2.4-( v id )/2 v high level input voltage ( v ih ) 2.2 --- 3.3 v low level input voltage ( v il ) v ss --- 0.7 v (i dd ) *3 --- 460 --- ma current consumption (i fl ) *4 4.0 6.0 6.5 ma(rms) power consumption *1 *2 --- (17.1) --- w i fl =6.0ma(rms) *2: the surface temperature caused by self heat r adiation of cell itself is specified on this item. *3: 8 color bars pattern *4: except the efficiency of fl inverter optical specification ( t a=25 c) item min. typ. max. unit remarks contrast ratio ( cr) --- 450 --- --- (upper+lower) --- 120 --- viewing angle ( cr 10) (left+right) --- 160 --- response time ( t on + t off ) --- 16 --- ms luminance ( l ) 350 450 --- cd/m 2 i fl =6.0ma(rms) lamp life time (mtbf)* 5 * 6 50,000 h *5 : conditions ; t a=25 c, i =6.0ma(rms), continuous lighting fl *6 : definitions of failure ; 1) lcd luminance becomes half of the minimum value. 2) lamp doesn?t light normally. www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (2/10) 2008-02-21(ver.0.2r) tentative unit : mm standard tolerance : 0.5 dimensional outline www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (3/10) 2008-02-21(ver.0.2r) tentative unit : mm standard tolerance : 0.5 dimensional outline www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (4/10) 2008-02-21(ver.0.2r) block diagram cn3 sequence of power supplies and signals rxin0+/- v v sfl fl 10% v sfl 10% v fl fl input voltage rxin1+/- rxin2+/- clk+/- v cm v id || 10ms (max.) 0.5ms (min.) 100ms (max.) 0.1ms (min.) 500ms (min.) 40ms (max.) 0ms (min.) 40ms (max.) 0ms (min.) 2sec(min.) 0ms(min.) 250ms(min.) dd v 0.2 0.2 3.0 v v v 3.0 v v 0.2 3sec ( min. ) 3sec ( min. ) 650ms ( min. ) cn 1 cn2 panel cntroller converter dc/dc gray scale manipulation voltage generation circuit y-driver ic liquid crystal panel fl fl x-driver ic 1024x768 pixels fl fl & connector lvds cn3 cn1 cn2 connector cn4 www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (5/10) 2008-02-21(ver.0.2r) timing chart tv tvw vsync tvsu tvhd th hsync tvfp tvbp tvd tvds de 767 768 12 768 th thw hsync thbp thfp thds thd de 1024 pixel nclk 12345 timing specification item symbol min. typ. max. unit horizontal period t h 1180 1344 1687 (clock) horizontal frequency f t h 47.4 48.363 60.8 khz h-sync pulse width t hw 8 136 - (clock) horizontal front porch t hfp 2 24 - (clock) horizontal back porch t hbp 6 160 - (clock) horizontal data sync period t hds 14 296 - (clock) horizontal display term t hd 1024 1024 1024 (clock) frame period t v 790 806 810 (line) vertical frequency f t v 50.0 60.0 65.0 hz v-sync pulse width t vw 2 6 - (line) v-sync set up time t vsu 8 - - (clock) v-sync hold time t vhd (thbp+16) - - (clock) vertical front porch t vfp 2 3 - (line) vertical back porch t vbp 6 29 - (line) vertical data sync period t vds 8 35 - (line) vertical display term t vd 768 768 768 (line) clock period t c 14.286 15.385 15.748 ns clock frequency f t c 63.5 65.0 70 mhz note 1) refer to ?timing chart? and lvds(thc63l vdm83r) specifications by thine electronics,inc. note 2) if nclk is fixed to "h" or "l" level for certain period while de is supplied, the panel may be damaged. note 3) if de is fixed to ?h? or ?l? level for certain period while nclk is supplied, the panel displays black with some flick er. note 4) please adjust lcd operating signal timing and fl driving frequency, to optimize the display quality. there is a possibility that flicker is observed by the in terference of lcd operating signal timing and fl driving condition (especially driving frequency), even if t he condition satisfies above timing specifications. note 5) do not make tv , th and tvds fluctuate. note 6) in case of using the long frame period, the det erioration of display quality, noise etc. may be occurred. note 7) nclk count of each horizontal scanning time should be always the same. v-blanking period should be ? n ? x ?horizontal scanning time?. ( n : integer) frame period should be always the same. www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (6/10) 2008-02-21(ver.0.2r) connector pin assignment for interface cn1 input signal connector: df14h-20p-1 .25h(56) / hirose electric co., ltd. mating connector: df 14-20s-1.25c(socket), df14- 2628scfa(contact) / hirose electric co., ltd. terminal no. symbol function 1 vdd power supply : +3.3v 2 vdd power supply : +3.3v 3 vss gnd 4 vss gnd 5 rxin0- negative lvds differential data input 0(-) 6 rxin0+ positive lvds differential data input 0(+) 7 vss gnd 8 rxin1- negative lvds differential data input 1(-) 9 rxin1+ positive lvds differential data input 1(+) 10 vss gnd 11 rxin2- negative lvds differential data input 2(-) 12 rxin2+ positive lvds differential data input 2(+) 13 vss gnd 14 clk- clock signal(-) 15 clk+ clock signal(+) 16 vss gnd 17 rxin3- negative lvds differential data input 3(-) 18 rxin3+ positive lvds differential data input 3(+) 19 sellvds lvds mapping select 2) 20 nc non connect note 1) please connect gnd pin to ground. don?t us e it as no-connect nor connection with high impedance. note 2) please refer page7&8 cn2 input signal connector: df14h-2p-1. 25h(56) / hirose electric co., ltd. mating connector: df14-2s-1.25c(socket) , df14-2628scfa(contact) / hirose electric co., ltd. terminal no. symbol function 1 ud/rl 1 select reverse scan 2 ud/rl 2 select reverse scan note) normal scan condition: ud/rl1 and ud/rl2 open. or ud/rl1 open and ud/rl2 input signal ?low?. reverse scan condition: short between ud/rl1 and ud/rl2. or ud/rl1 open and ud/rl2 input signal ?high? cn3,4 ccfl power source connector: bhr-04vs-1 / japan solderless terminal mfg co., ltd. mating connector: sm03(7-d1)b-bhs-1n- tb(lf) / japan solderless terminal mfg co., ltd. terminal no. symbol function 1 v flh1 ccfl power supply ( high voltage) 2 v flh2 ccfl power supply ( high voltage) 3 nc ---- 4 v fll ccfl power supply (low voltage) www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (7/10) 2008-02-21(ver.0.2r) recommended transmitter (thc63lvdm83r by thine electronics, inc.) to lta150b851 interface assignment case1; cn1 no.19pin : ?low? thc63lvdm83r input terminal no. input signal (graphics controller output signal) lta150b85xf interface (cn1) symbol terminal symbol function output signal symbol terminal symbol ta0 51 r0 red pixels display data (lsb) ta1 52 r1 red pixels display data ta2 54 r2 red pixels display data ta3 55 r3 red pixels display data ta4 56 r4 red pixels display data ta5 3 r5 red pixels display data ta6 4 g0 green pixels display data(lsb) ta- ta+ no.5 no.6 rxin0- rxin0+ tb0 6 g1 green pixels display data tb1 7 g2 green pixels display data tb2 11 g3 green pixels display data tb3 12 g4 green pixels display data tb4 14 g5 green pixels display data tb5 15 b0 blue pixels display data (lsb) tb6 19 b1 blue pixels display data tb- tb+ no.8 no.9 rxin1- rxin1+ tc0 20 b2 blue pixels display data tc1 22 b3 blue pixels display data tc2 23 b4 blue pixels display data tc3 24 b5 blue pixels display data tc4 27 hsync horizontal synchronization signal tc5 28 vsync vertical synchronization signal tc6 30 de compound synchronization signal tc- tc+ no.11 no.12 rxin2- rxin2+ td0 50 r6 red pixels display data td1 2 r7 red pixels display data (msb) td2 8 g6 green pixels display data td3 10 g7 green pixels display data(msb) td4 16 b6 blue pixels display data td5 18 b7 blue pixels display data (msb) td6 25 gnd gnd td- td+ no.17 no.18 rxin3- rxin3+ clk in 31 clk data sampling clock tclk- tclk+ no.14 no.15 clk- clk+ g0 r5 r4 r3 r2 r1 r0 g5 b0 b1 g4 g1 b4 b5 g3 g2 b2 b3 ta 0 tb 0 b7 b6 g7 g6 r7 r6 tb 6 tb 5 tb 4 tb 3 tb 2 tb 1 tc 6 tc 5 tc 4 tc 3 tc 2 tc 1 tc 0 ta 3 ta 2 ta 1 ta 4 ta 5 ta 6 td 6 td 5 td 4 td 3 td 2 td 1 td 0 de vsync hsync rx in0 rx in1 rx in2 rx in3 gnd www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (8/10) 2008-02-21(ver.0.2r) recommended transmitter (thc63lvdm83r by thine electronics, inc.) to LTA150B851F interface assignment case2; cn1 no.19 pin : ?open? or ?high? thc63lvdm83r input terminal no. input signal (graphics controller output signal) lta150b85xf interface (cn1) symbol terminal symbol function output signal symbol terminal symbol ta0 51 r2 red pixels display data ta1 52 r3 red pixels display data ta2 54 r4 red pixels display data ta3 55 r5 red pixels display data ta4 56 r6 red pixels display data ta5 3 r7 red pixels display data (msb) ta6 4 g2 green pixels display data ta- ta+ no.5 no.6 rxin0- rxin0+ tb0 6 g3 green pixels display data tb1 7 g4 green pixels display data tb2 11 g5 green pixels display data tb3 12 g6 green pixels display data tb4 14 g7 green pixels display data (msb) tb5 15 b2 blue pixels display data tb6 19 b3 blue pixels display data tb- tb+ no.8 no.9 rxin1- rxin1+ tc0 20 b4 blue pixels display data tc1 22 b5 blue pixels display data tc2 23 b6 blue pixels display data tc3 24 b7 blue pixels display data (msb) tc4 27 hsync horizontal synchronization signal tc5 28 vsync vertical synchronization signal tc6 30 de compound synchronization signal tc- tc+ no.11 no.12 rxin2- rxin2+ td0 50 r0 red pixels display data (lsb) td1 2 r1 red pixels display data td2 8 g0 green pixels display data (lsb) td3 10 g1 green pixels display data td4 16 b0 blue pixels display data (lsb) td5 18 b1 blue pixels display data td6 25 gnd gnd td- td+ no.17 no.18 rxin3- rxin3+ clk in 31 clk data sampling clock tclk- tclk+ no.14 no.15 clk- clk+ ta 0 tb 0 tb 6 tb 5 tb 4 tb 3 tb 2 tb 1 tc 6 tc 5 tc 4 tc 3 tc 2 tc 1 tc 0 ta 3 ta 2 ta 1 ta 4 ta 5 ta 6 td 6 td 5 td 4 td 3 td 2 td 1 td 0 de vsync hsync rx in0 rx in1 rx in2 rx in3 gnd r2 r3 r4 r5 r6 r7 g2 g3 g4 g5 g6 g7 b2 b3 b4 b5 b6 b7 r0 r1 g0 g1 b0 b1 www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (9/10) 2008-02-21(ver.0.2r) 256k (k=1024) colors combination table display r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 gray scale level black llllllll llllllll llllllll l 0 blue llllllll llllllll hhhhhhhh --- green l l llllll hhhhhhhh l l llllll --- light blue llllllll hhhhhhhh hhhhhhhh --- red hhhhhhhh l l llllll llllllll --- purple hhhhhhhh l l llllll hhhhhhhh --- yellow hhhhhhhh hhhhhhhh l l llllll --- basic color white hhhhhhhh hhhhhhhh hhhhhhhh l255 black llllllll llllllll llllllll l 0 lllllllh ll llllll llllllll l 1 llllllhl ll llllll llllllll l 2 llllllhh ll llllll llllllll l 3 lllllhll ll llllll llllllll l 4 : : : : : : l5 l252 hhhhhhlh l l llllll llllllll l253 dark light hhhhhhhl l l llllll llllllll l254 gray scale of red red hhhhhhhh l l llllll llllllll red l 255 black llllllll llllllll llllllll l 0 llllllll lllllllh ll llllll l 1 llllllll llllllhl ll llllll l 2 llllllll l lllllhh ll llllll l 3 llllllll lllllhll ll llllll l 4 : : : : : : l5 l252 llllllll hh hhhhlh l l llllll l253 dark light llllllll hh hhhhhl l l llllll l254 gray scale of green green l l llllll hhhhhhhh l l llllll gr een l255 black llllllll llllllll llllllll l 0 llllllll llllllll lllllllh l 1 llllllll llllllll llllllhl l 2 llllllll llllllll llllllhh l 3 llllllll llllllll lllllhll l 4 : : : : : : l5 l252 llllllll llllllll hh hhhhlh l243 dark light llllllll llllllll hh hhhhhl l254 gray scale of blue blue llllllll llllllll hhhhhhhh blue l255 black llllllll llllllll llllllll l 0 lllllllh lllllllh lllllllh l 1 llllllhl llllllhl llllllhl l 2 llllllhh llllllhh llllllhh l 3 lllllhll lllllhll lllllhll l 4 : : : : : : l5 l252 hhhhhhlh hhhhhhlh hhhhhhlh l253 dark light hhhhhhhl hhhhhhhl hhhhhhhl l254 gray scale of white & black white hhhhhhhh hhhhhhhh hhhhhhhh white l255 www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
LTA150B851F (10/10) 2008-02-21(ver.0.2r) for safety ! lcd module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. in using our modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in engineering information no.ee-n001,"caut ions and instructions for toshiba lcd modules". refer to individual specifications and technical data s heets (hereinafter called "td") for more detailed technical information. 1) special purposes a) toshiba matsushita display technology's standard lcd modules have not been customized for operation in extreme environments or for use in applications where performance fa ilures could be life-threatening or otherwise catastrophic. b) since toshiba matsushita display technology's standar d lcd modules have not been desi gned for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed toshiba matsushita display technology's published specification limits. c) in addition, since toshiba matsushita display techno logy standard lcd modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to traffic collision avoidance system and air traffic indicator), in milit ary defense or weapons systems, in critical indu strial process-control systems (e.g., t hose involved in the production of nuclear energy), or in critical medical devi ce or patient life-support systems. 2) disassembling or modification do not disassemble or modify the module. it may damage sensitive pa rts inside lcd module, and may cause scratches or dust on the display. toshiba matsushita display technology doses not warrant the module, if customer di sassembled or modified it. 3) breakage of lcd panel do not ingest liquid crystal material, do not inhale this material, and do not contact the material with skin, if lcd panel is broken and liquid crystal material spills out. if liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. if this material contact with skin or cl oths, wash it off immediately with al cohol and rinse thoroughly with water. 4) glass of lcd panel be careful with chips of glass that may cause injuring fingers or skin, when the glass is broken. 5) electric shock disconnect power supply before handling lcd module. do not touch the parts inside lcd module and the fluorescent la mp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) absolute maximum ratings and power protection circuit do not exceed the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise lcd module may be damaged. employ protection circuit for power supply, whe never the specification or td specifies it. suitable protection circuit should be applied for each system design. 7) recommended operation conditions the performance and quality of the lcd panel are warranted only when the lcd panel is used within ?the recommended operation conditions?. toshiba matsushita display technolo gy co., ltd. never warrants the performance and quality of the lcd panel when you use the lcd panel over ?the recommended operation conditions?, although within ?the absolute maximum rating?. to use the lcd panel over ?the recommended operation conditions? may have bad influence on the characteristics and reliability of the lcd panel and may shorten the life of the lcd panel. therefore, when designing the whole set, not to be over ?the recommended operation c onditions?, you should fully take care of supply voltage change, characteristic of connection parts, serge of input-and-output li ne, and surrounding temperature. 8) disposal when dispose lcd module, obey to the applicable environmental regulations. www.speclcd.com www.speclcd.com www.datasheet.co.kr datasheet pdf - http://www..net/
|
